On the left is anthropologie's jeweled lacewing necklace. Made of brass, jasper, a bit of silk and a couple bits of aquamarine, it costs a whopping $548 on the website. On the right is my DIY version of this necklace, made of the same materials. Not counting the expense of tools (metal snips, metal file, hammer, anvil, metal punch) which I already owned, this necklace cost me just under $50 (and some 6 or 7 hours of labour) to make. Less than 1/10 the cost of the original. Instructions for the difficult part (the bezel-set jasper) follow below!
but first let's take one more longing look at how anthro has styled this necklace, shall we? A friend of mine did an online double-take when I said "butterfly necklace" ("...butterflies?!") but really, I think this reads as less "Mariah Carey" and more Byzantine (and I really dug the jewelry in the fall 2013 D&G runway show).
To make this necklace, you need some stuff. A fair bit of stuff , in fact. You need 17 brass butterfly stampings. I tracked down the same ones used in the original necklace at a shop called Metalliferous. They are, hands down, the nicest brass stampings I've ever worked with - way heavier than I'd expected, they give a nice, weighty feel to the necklace. You'll also need two jasper cabochons. The large, triangular-shaped one should be about 3" wide (mine is only 2.5" wide - I struggled to find anything larger), and an oval one about 2" long (mine is only 1/5" long). You'll need sheet brass to make a bezel setting for the large jasper stone (I got mine at the hardware store. It was 0.32" thick). You'll need jump rings to attach most of the butterflies to each other. You'll need a bit of hot pink silk thread, six faceted aquamarine rondelles, 12 clear glass seed beads and 12 brass crimp beads for the butterflies that are tied together instead of linked with jump rings.
You'll also need tools: metal snips to cut the brass, a metal file to take any sharp edges off the butterflies and to file down the bezel, a hammer and anvil to shape the two butterflies that sit on the large jasper stone, a metal punch to make holes in your butterflies' wings for linking them together (some have only two holes, some have three, some have four - so if you order pre-punched stampings to avoid this step, you'll have to order butterflies with four holes punched in them and then just have a few extra holes in some of your butterflies), needle nosed pliers for opening and closing the jump rings, scissors for cutting thread, and a bit of superglue for affixing the stones to brass.
The most difficult part of this necklace (I think) is making the rustic bezel setting for the large jasper stone. Mine is not perfect, but I was able to hide some of the gaps/rough spots by careful placement of the hammered butterflies.
Here's how I made mine:
cut around your template - but cut wider than your outline as you need something to turn up to make the bezel setting. Use your metal file to soften the sharp edges before proceeding, so you don't run the risk of cutting your fingers on the sharp brass!
using needle-nosed pliers, start bending up the edge of the brass. The tips of my pliers are touching the outline I made with my paper stencil.
Keep bending up the metal. Periodically stop and check how your stone is fitting inside the setting. When it seems fairly tight (when the stone kind of snaps into place), it's time to get ready for gluing. Before you do, however, break out your metal file and file the sharp edges (see right, above), smoothing the sides of the bezel.
I use a gorilla glue epoxy (superglue) that is suitable for indoor and outdoor use and stands up to humidity and both heat and cold. In short; it'll work under all conditions! File the back of your stone a bit with the metal file before gluing, and thoroughly brush away any stone dust. The stone will adhere better if has an uneven/rough surface (instead of smooth and polished). Fill the bezel setting with a nice big puddle of glue that is spread all the way to the edges. Press the stone in. Hold it for a minute or two (or five!) and let it dry for a few hours before you work with it anymore.
After the stone has had some time to set, get out your hammer, pliers, and file. Continue to gently work the sides of the bezel close around the stone, and file everything excessively at the end, to smooth the sides and eliminate sharp edges.
I won't walk through how to punch holes in the stampings. There are other online tutorials for that. The two butterflies that sit on top of the jasper stone have a roughed-up textural finish, and are slightly rounded. The rounding is achieved by hammering the stampings on an anvil. Hold the butterfly with the edged side down on the anvil and gently hammer. The stamping will start to gently curve up. After hammering a bit, check to see if the butterflies sit flush to the front of the jasper stone. If not, keep working them.
(Use a similar approach to get the bottom butterfly to wrap around the smaller jasper stone (then glue the stone to the butterfly using epoxy again. Don't forget to rough up the underside of the brass butterfly and the stone where it will touch, before you glue!)
When you have the proper shape, it's time to make the surface more textured: some rough filing (at odd angles) with the metal file will help achieve this look.
Here's a diagram, if it helps of how I tied together the bottom six butterflies. It's quite simple: tie a simple overhand knot near to the end of some silk beading cord (I used size 6). Slip on a brass crimp bead; crimp it. Slip on a clear glass seed bead. Put the thread through the punched hole in the butterfly and knot it tightly, without leaving any extra thread between the knot and the glass seed bead. Slip on the faceted aquamarine rondelle, and then tie tightly to the butterfly above, knotting the thread. Slip on another clear glass seed bead, then a brass crimp bead. Press the crimp bead and seed bead up against the knot and then crimp the crimp bead with your needle-nosed pliers. Then tie another overhand knot snug against the second crimp bead. Clip thread close to the knot.
And then it's done! Ta-dah!!
No comments:
Post a Comment